How to decorate a fireplace, stairs and a window with a pine garland

Christmas Tree · Tips and Choices

How to decorate a fireplace, stairs and a window with a pine garland

A pine garland helps to unite the Christmas decor in the room: emphasize the line of the fireplace portal, decorate the stairs or create a green frame near the window. The best result starts with measurement and thought out shape, followed by lights, ribbons and decorations.

This article is about decorative garland of artificial coniferous branches. An electric LED garland is a separate product that can be added to the green base if desired. Their lengths and installation methods must be calculated separately.

Which coniferous garland to choose for the interior

For a noticeable three-dimensional composition, not only meters are important, but also the width after straightening the branches. A thin line of greenery and a thick cast garland will occupy different places on the same shelf or near the window.

Green garlands of the Kovalivska and Vienna series have a length of 2.5 m and needles made of 100% molded PE-polyethylene. After fluffing, the declared diameter is about 45 cm and the weight is about 2.1 kg. The actual volume depends on how the feet are shaped.

It is worth choosing between series based on the texture of the twigs and the appearance next to other needles in the room. The same length is not enough for two compositions to be visually perceived in the same way.

How to calculate the required length

Measure exactly the future route of the garland, including dips and sags. The length of a straight shelf or handrail is not equal to the length of the wavy composition on them.

1. Mark the beginning and end of the design.
2. Lay a soft cord along the route: repeat all the bends and desired descents.
3. Remove the cord and measure it with a tape measure.
4. If two garlands are needed, provide for the joining point and possible overlap.
5. Check separately if the width of the spread needle will fit.

Don't try to compensate for the lack of length by pulling too hard. It is better to simplify the form or change the borders of the design. For a long composition, check the load of each support, not just the strength of the joint between two segments.

How to arrange a fireplace or a decorative portal

It is convenient to try a symmetrical composition with two identical descents on a decorative portal without heating. For a less formal look, one edge can be made longer and the other left short. First, determine the main line and support points so that the greens do not slide off the shelf.

Branches on the side of the wall can be directed along the surface, and the front ones - outward and slightly downward. This is how a voluminous front edge is formed. Do not pinch all the feet between the shelf and the decor: part of the needle should remain visible.

For a working fireplace or an electric fireplace with heating first check the instructions for the appliance and the permissible placement of objects around it. The decor should not be near a flame, on heated parts or block the outlet of hot air. If there is no required distance, frame the adjacent wall or other cold surface. For light accents in the conifer composition itself, use flameless LED candles.

The recommendations of the US Fire Service also emphasize moving holiday decorations away from heat sources; more details - in reminders about the holiday decoration.

How to decorate the stairs with a pine garland

On the stairs, it is important to maintain a free passage and the ability to comfortably hold on to the handrail. Place the composition on the outside of the fence or in another area where needles, ribbons and wires will not interfere with movement. Especially carefully check the lower descent: it should not lie on the steps.

For a calm design, lay a garland along the fence line. For waves, first measure them with a cord so that adjacent sags have a consistent rhythm. It is logical to place large bows near the attachment points, but they themselves do not replace the support.

Choose fasteners according to the material of the fence and the total weight. Soft reusable ties can be hidden behind the base; be careful not to scratch the surface or pinch the electrical wire. Support each section according to its load, rather than hanging the entire length from one end.

Window design options

The easiest option is a green composition on the windowsill, if its depth allows you to place the decor stably. Check the access to the handle, the opening of the sash and the absence of contact with the heater under the window. The needle should not be pinched between the frame and the sash.

The second option is to decorate the upper part of the opening or create a frame with slopes. Do not use the curtain rod as a support without confirming the permissible load. A large garland requires fasteners designed for the appropriate weight and surface.

If the window is small, it is not necessary to frame the entire perimeter. One asymmetric area can let in more daylight and create a distinct accent without overfilling the space.

How to add lights and decorations

It is more convenient to weave in the light after the fitting, but before the final placement of small decor. Lay the wire freely, without tight bends and pinching with fasteners. Leave access to the power supply or battery compartment.

U catalogs of LED garlands check the length of the light part, the power supply and the conditions of use of the specific product. The length of the illumination does not need to be equated to 2.5 m of the green base: the wrapping consumes the additional length. If you are planning a thin garland of dew, it will come in handy explanation of the principles of its placement among needles.

For a complete design, choose one ribbon and two or three textures of jewelry. For example, matte balls, textiles and cones. It is not necessary to fill every branch: the repetition of several accents along the composition creates a clear rhythm.

Along with the garland can be used green Christmas wreath, repeating the color of the bow. For a Christmas tree, wreath and garland in the same room, it is useful to choose a common palette in advance - examples are in guides from the colors of the green Christmas tree decor.

How to keep in shape after the holidays

Before packing, remove the decorations and lights, if they were added separately. Remove the dust with a soft brush, make sure the garland is dry, and fold it carefully without sharp bends of the base. Do not put heavy boxes on top: they can crush the feet.

Label the box with the model name and length. If you like the design, take a picture of it and write down the locations of the supports: next season, it will help to reproduce the composition faster. Before re-installation, check the condition of the fasteners and wires anyway.

Frequently asked questions

Read also

• Christmas wreath on the door: how to choose the size and fix it beautifully